壁厚 英语是什么意思 - 英语翻译

• wall thickness
• wall thicknesses
• wall thick

在 中文 中使用 壁厚 的示例及其翻译为 英语

壁厚取决于桩的深度。
Which dock depends on depth.

轧辊转速不当也会影响壁厚精度。
Improper roller speed will also affect the accuracy of wall thickness.

降低最高设计温度，但不影响壁厚；.
(a) A decrease in the maximum design temperature, not affecting thickness;

现实存在的问题意味着壁厚不可能无限量地减少。
Practical issues mean wall thicknesses cannot be reduced indefinitely.

提高最低设计温度，但不影响壁厚；.
(b) An increase in the minimum design temperature, not affecting thickness;

管子壁厚δ=（P*D）/（2*σ/S）其中S为安全系数；.
Pipe wall thickness δ=(P* D)/(2* σ/ S) where S is the safety factor;

星球上最大的生物是菌丝团，有一个细胞壁厚。
The largest organism on the planet is a mycelial mat, one cell wall thick.

选用Q235钢管，壁厚4mm灯杆高10米；.
Q235 steel tube with a wall thickness of 4mm and a height of 10m;

降低原始最大设计温度，但不影响壁厚；.
(a) A decrease in the initial maximum design temperature, not affecting thickness;

深度超过壁厚5%的外结疤应修磨。
Depth of more than 5% of the wall outside the scar should be grinding.

提高原始最低设计温度，但不影响壁厚；.
(b) An increase in the initial minimum design temperature, not affecting thickness;

如果壁厚大于3mm，建议使用20-40℃的低温模具。
If the wall thickness is greater than 3 mm, a low temperature mold of 20 to 40° C is recommended.

Logan根据ICON工程团队对壁厚的规格建立了Revit系列。
Logan built a Revit family to the wall-thickness specifications of the ICON engineering team.

检查壁厚是否太薄(设计或制造),应直接填充稀释剂区域。
Check if the wall thickness is too thin(design or manufacture), the thinner area should be filled directly.

无须调整模具，滚塑产品的壁厚可以自由调整（2mm以上）。
No need to adjust the mould, the wall thickness of rotational molding products can be adjusted freely(above 2mm).

软管壁厚仅2mm，气道短而直，气压损失小。
The wall thickness of the hose is only 2mm, the airway is short and straight, and the air pressure loss is small.

这个变形影响因素有2个，一个是卡扣的壁厚，一个卡扣的长度。
There are two factors influencing this deformation, one is the wall thickness of the buckle and the length of one buckle.

检查壁厚是否太薄(设计或制造)，较薄的区域应直接充填．.
Check if the wall thickness is too thin(design or manufacture), the thinner area should be filled directly.

主要问题是投资高，成本高，制造工艺复杂，壁厚和椭圆度公差大。
The main problems are high investment, high cost, complicated manufacturing process, and large wall thickness and ellipticity tolerance.

查看壁厚是不是太薄(规划或制造)，较薄的区域应直接充填．.
Check if the wall thickness is too thin(design or manufacture), the thinner area should be filled directly.

恩欣格在PEEK管材领域同样拥有丰富的经验，可提供各种标准管尺寸和壁厚。
Ensinger also has extensive experience in the field of PEEK tube, offering a wide range of standard tube sizes and wall thicknesses.

这种壁厚要求所有管材均能满足，从而很难体现弯管的优势。
This wall thickness requires all pipes to be able to meet, which is difficult to reflect the advantages of bend.

产品中空无缝，壁厚均匀，可以调整壁厚，使产品具高强度。
The product is hollow seamless, wall thickness uniformity, can adjust the wall thickness, so that products with high strength.

其壁厚不仅可以很薄，而且可以大大简化生产过程，提高生产效率。
Its wall thickness can not only be very thin, but also greatly simplify the production process and improve production efficiency.

使用无缝钢管更昂贵，但允许较小的壁厚和重量，这会影响设计和成本。
Although it is more expensive to use a seamless pipe, it allows for smaller wall thickness and pipe weight which can affect design and costs.

这包括感受元件最佳形状的选择，以及弹性金属管的最佳材料和壁厚的选择。
This includes feelings of selecting the best shape of elements, as well as the best material elastic metal pipe and wall thickness options.

如果您想切割上面的松下模具横截面，您会注意到整个壁厚约为2-3毫米。
If you were to cut a cross-section of the Panasonic mold above you would notice that the wall thickness is approximately 2-3mm thick throughout.

无缝钢管可以承受高压，当然其壁厚也会随之增加，这需要根据压力要求来进行设计。
Seamless pipe can withstand high pressure, of course, the wall thickness will also increase, which requires pressure requirements according to design.

在增加模腔壁厚和降低压力方面，3D打印模具(尤其是高注塑温度)在某种程度上更为灵活。
In terms of increasing cavity wall thickness and reducing pressure, 3D printing moulds(especially high injection temperature) are more flexible to some extent.

型坯厚度控制装置用于控制型坯壁厚，控制点最多达128点，一般为20～30点。
The parison thickness control device is used to control the parison wall thickness, the control point up to 128 points, usually 20 to 30 points.