The following triggers have built-in retry support.
평가자 키, 재시도 및 일시적 오류 처리 패턴 설명.
Describe the Valet Key, Retry and Transient Fault Handling Patterns.
정부는 장교를 재시도하고 약속했다.
The government promised to retry the officers.
만약 그래도 안되신다면 1분 후에 재시도 부탁드립니다.
If that doesn't work, please try again in a minute.
기본 네트워크 재시도 시간 제한의 기본값은 180초입니다.
The default value of Default Network Retry Timeout is 180 seconds.
재시도 전에 현재 진행 중인 컴파일이 끝날 때까지 기다려주세요.
Please wait for your other compile to finish before trying again.
대부분의 상황에서이 오류 이 때 발생 데이터베이스 "수출입 재시도 "입니다 부정한.
In most situations, this error It occurs when database"Exim Retry"is corrupt.
R 재시도 SNMP 쿼리를 보내는 별도의 횟수(기본값 = 0).
R retries Number of extra times to send the SNMP queries(default= 0).
클라이언트가 이 요청을 재시도하는 경우, 재시도에서의 요청 id는 123456이어야만 한다.
If the client retries this request, the request id in the retry must by 123456.
PS-300B 설치 CD 가 들어 있지 않음 PS-300B (1.0 또는 이후 버젼)CD-ROM을 디스크 드라이브에 넣고 재시도.
PS-300B install CD is not inserted. Insert the PS-300B(version 1.0 or newer)CD-ROM to the disk drive, and then try again.
I 주소 쿼리를 보낼 로컬 인터페이스의 주소 -t 초 IGMP 쿼리의 제한 시간(기본값 = 3초) -r 재시도 SNMP 쿼리를 보내는 별도의 횟수(기본값 = 0) -?
T seconds Timeout in seconds for IGMP queries(default= 3 seconds)-r retries Number of extra times to send the SNMP queries(default= 0)-?
재시도 횟수, 각 시도 사이의 지연 시간 및 시도 실패 후 수행할 작업을 지정 하는 적절 한 재시도 전략을 사용 합니다.
Use an appropriate strategy for the retries, which specifies the number of times it should retry and the delay between each attempt.
당신이 가까운 경매 직후에 체크아웃 할 수 없는 경우에,몇 분 동안 기다려주십시오 및 재시도 지불은 3 일 안에 완료되어야 합니다.
If you can't checkout immediately after auction close,please wait for a few minutes and retry Payments must be completed within 3 days.
이제, 이 요청은 목적지 X에 도달하지 못한 엄청난 수의 요청을 만들어낼 뿐 아니라 모든 실패한 요청이 다시 큐에 재시도로 쌓이게 됩니다.
Now, not only does this create a large backlog of requests which have yet to reach destination X, but also every failed event is put back to retry in the queue.
단계(1005)에서, 루틴 "identifyTargetDevices"은 설치 메시지가 타겟 장치로 전송되고 타겟 장치에 대한 재시도 카운트를 0으로 설정하는 것을 표시한다.
In step 1005, the routine“identifyTargetDevices” notes that an installation message was sent to the target device and sets a retry count for the target device to 0.
그러나, n번의 재시도 후에, 소재지 센서가 유효한 사전-프로그래밍된 위치를 픽업하는 것을 실패하면, 블록(445)에서 다양한 플랫폼 정책 드라이버 액티비티가 수행될 수 있다.
However, if after n retries, the locality sensor fails to pick up a valid pre-programmed location, a variety of platform policy driver activities may be performed, in block 445.
작업이 실패할 경우 해당 작업의 재시도 횟수의 최대치를 설정하였고 현재의 작업환경이 test 일 경우에는 백그라운드에서 처리되지 않도록 설정했습니다.
We have set the maximum number of times that a job will be tried if it fails and also an option that will stop tasks being processed in the background if the current environment is test.
English
عربى
Български
বাংলা
Český
Dansk
Deutsch
Ελληνικά
Español
Suomi
Français
עִברִית
हिंदी
Hrvatski
Magyar
Bahasa indonesia
Italiano
日本語
Қазақ
മലയാളം
मराठी
Bahasa malay
Nederlands
Norsk
Polski
Português
Română
Русский
Slovenský
Slovenski
Српски
Svenska
தமிழ்
తెలుగు
ไทย
Tagalog
Turkce
Українська
اردو
Tiếng việt
中文