What is the translation of " 信号功率 " in English?

• signal power

Examples of using 信号功率 in Chinese and their translations into English

插入损耗涉及信号功率的损失。
Insertion loss involves the loss of signal power.

如前所述，高频信号功率可能因环境条件而降低。
As previously stated, signal power at high frequencies can be diminished by environmental conditions.

插入损耗涉及到信号功率的损失。
Insertion loss involves the loss of signal power.

它被定义为信号功率与噪声功率之比。
It is defined as the ratio between the signal power and the noise power..

信号功率测量通常用dBm（分贝相对于1毫瓦）表示。
Signal power is often measured in dBm(decibels relative to 1 mW).

这种效应减低了可接收的信号功率。
This type of effect reduces the signal power that can be received.

这种效应减低了可接收的信号功率。
This effect reduces the signal power that can be received.

插入损耗是由电缆引起的信号功率衰减的结果。
Insertion loss is the result of signal power attenuation caused by the cable.

信号功率和噪声功率的比值。
The ratio of the signal power and noise power..

系统开通测试包括信号功率水平和光信噪比(OSNR)测量，它们对于重复越洋或架空链路均十分重要。
This includes signal power level and optical signal-to-noise ratio(OSNR) measurements, which are important in both repeated transoceanic or festoon links.

查看设备的信号功率，过滤出更接近你的设备的信号功率.
See the signal power of devices and filter the ones that are closer to you.

这些反射作为瓶颈，阻止了信号功率到达目的地。
These reflections act as bottlenecks, preventing the signal power from reaching the destination.

请注意，在传播路径中使用了四个掺铒光纤放大器（EDFA）来提升信号功率。
(Note that four erbium-doped fiber amplifiers(EDFAs) are used to boost the signal power along the propagation path.).

Kumar按下一个按钮来增加收发信机的信号功率，然后重复。
Kumar presses a button to increase the signalling power of the transceiver, and repeats himself.

预计这种方式还将更有效地利用信号功率并提高带宽使用效率。
It's also expected to make better use of signal power and more efficient use of bandwidth.

信号功率测量通常用dBm（分贝相对于1毫瓦）表示。根据上述公式，噪声电源电阻在室温下的噪声功率，用dBm表示为：.
Signal power is often measured in dBm(decibels relative to 1 milliwatt). From the equation above, noise power in a resistor at room temperature, in dBm, is then:.

这种效应降低了信号功率。
This effect reduces the received signal power.

这种效应减低了可接收的信号功率。
This effect reduces the power of the received signal.

这种效应减低了可接收的信号功率。
This effect reduces the received signal power.

同时，系统还起到将信号功率放大的作用。
At the same time, the system also plays a role in amplifying the signal power.

发射点和接收点之间的电磁信号功率损失。
The loss in power of electromagnetic signals between transmission and reception points.

发射点和接收点之间的电磁信号功率损失。
Power loss of electromagnetic signals between transmission and reception points.

这种效应减低了可接收的信号功率。
This reduces the strength of the signal received.

DBc单位表示输出噪声对期望信号功率的归一化。
The unit dBc indicates the normalization of the output noise to the desired signal power.

Attenuation衰减发射点和接收点之间的电磁信号功率损失。
The loss in power of electromagnetic signals between transmission and reception points.

但与此同时，阻抗必须保持较低，方能將足够的信号功率传送到接收端。
At the same time, however, the impedance must be kept low so that adequate signal power will be delivered to the receiving end.

计算介电常数需要知道某块地方反射的信号功率，而这只能由研究人员估算出来。
Calculating permittivity requires knowing the signal power reflected by the bright patch, something the researchers could only estimate.