What is the translation of " 设计压力 " in English?

• design pressure

Examples of using 设计压力 in Chinese and their translations into English

设计压力P≤1.6MPa；.
Design pressure P is no more than 1.6MPa;

设计压力一般用Pe表示。
The design pressure is generally expressed by Pe.

设计压力和设计温度；.
(a) the design pressure and temperature;

设计压力不得低于最高工作压力压力。
Design pressure shall not be less than 10% above maximum working pressure..

试验压力应不低于罐体设计压力的1．5倍。
The test pressure shall be not less than 1.5 times the design pressure.

设计压力：一般为0.4MPa，大可达1.6MPa。
Design pressure: generally 0.4MPa, up to 1.6MPa.

球罐的主要参数为设计压力和设计温度。
The key components of the design conditions are the design pressure and the design temperature.

通过平台减缓设计压力.
Reducing design pressure through platforms.

这一压力必须至少是喷雾器设计压力的三分之二。
This shall be at least two-thirds of the design pressure of the aerosol dispenser.

设计压力低：简易压力容器的设计压力不超过1.6Mpa。
The design pressure is low: the design pressure of the simple pressure vessel does not exceed 1.6Mpa.

设计压力应比最高工作压力略高，并且应不小于安全阀的开启压力。
The design pressure should be slightly higher than the maximum working pressure and should not be less than the opening pressure of the safety valve.

反应容器（釜体）:根据容量大小及物料反应要求设计压力来确定板材厚薄；.
The reaction vessel(cavity): according to the size of the capacity and material reaction requirements design pressure to determine the thickness of the sheet;

可以针对一系列设备结构尺寸和设计压力提供客户定制型解决方案。
Customer-specific solutions can be offered from a wide array of machine sizes and design pressures.

同样重要的是避免建筑设计压力,如角90度或更少。
It is also important to avoid architectural design pressures, such as an angle of 90 degrees or less.

试验压力为板式换热器设计压力的1.25倍，保压30分钟。
The test pressure is 1.5 times the design pressure of the heat exchanger for 30 minutes.

同样重要的是避免建筑设计压力,如角90度或更少。
It is also important to avoid building stress into the design, such as corners that are 90 degrees or less.

试验压力为设备设计压力的1.25倍，保压30分钟。
The test pressure is 1.5 times the design pressure of the heat exchanger for 30 minutes.

气密性试验压力是容器的设计压力，空气压力试验压力是设计压力的1.15倍。
The test pressure is different, and the air tightness test pressure is 1.15 times of the design pressure of the container.

其次试验压力不同，气密性试验压力为容器的设计压力，气压试验压力为设计压力的1.15倍。
Secondly, the test pressure is different, and the air tightness test pressure is 1.15 times of the design pressure of the container.

(2)防“爆炸减压”2002年，美国石油学会标准API6D规定：设计压力高于ASMEClass600等级的阀门产品必须设计防“爆炸减压”。
In 2002, the American Petroleum Institute Standard API 6D provides: design pressure higher than ASME Class 600 grade valve products must be designed to"explosion decompression.".

B．设计压力的1．15倍.
Times the design pressure.

试验压力应为设计压力的1.5倍。
Minimum test pressure shall be 1.5 times the maximum design pressure.

更高的定制设计压力是可用的。
Higher design pressures are available.

随着设计压力的增加，许多以前的经验不再适用。
With the increase of design stress, many previous experiences no longer apply.

可以耐温度200℃，低温度可承受-38℃，设计压力可承受3.0MPa；.
Can withstand a maximum temperature of 200° C, a minimum temperature of -38° C, and a maximum design pressure of 3.0MPa;

这类气体钢瓶设计压力大于12Mpa（125kgf/cm2），称为高压气瓶。
Such gas cylinders are designed to have a pressure greater than or equal to 12 MPa(125 kg/cm2) called high pressure cylinders.

设计压力贮器时将使用的设计控制和设计检验方法、程序和系统行动；.
(b) the design control and design verification techniques, processes, and systematic actions that will be used when designing the pressure receptacles;

福特一直在使用类似技术来设计压力较小的操作工位，以增强其制造流程。
Ford has been using the same type of technology to design less physically stressful workstations to enhance its manufacturing processes.

但是，液压机制造商对此有很多控制权，可以设计压力机来处理所有负载大小。
However, hydraulic press manufacturers have a lot of control over this and can design presses to handle all load sizes.

根据用户要求设计工作压力.
Design work pressure according to user requirements.