英語 での High input impedance の使用例とその 日本語 への翻訳
{-}
-
Colloquial
-
Ecclesiastic
-
Computer
-
Programming
High input impedance: 1012.
A resistor value ashigh as 100kΩ is acceptable due to the high input impedance of the circuit.
The buffer's high input impedance results in minimal loading on the oscillator.
These miniature, high-precision,low quiescent current amplifiers offer high input impedance and rail-to-rail output swing within 15 mV of the rails.
Also, the high input impedance of the receivers allows more devices to be attached to the lines.
This miniature, high-precision,low quiescent current amplifier offers high input impedance and rail-to-rail output swing within 15 mV of the rails.
Its high input impedance(1000M ohm) make it suitable for measurement of high impedance voltage circuits.
The MUX508 and MUX509 have very low on and off leakage currents,allowing these multiplexers to switch signals from high input impedance sources with minimal error.
Their high input impedance does not affect the characteristic impedance of the transmission line, thus allowing back termination.
The 5350 is a low-priced digital electrometer with 5½-digit display.It can measure voltage with high input impedance of 1013 Ω or higher and wide-ranging current from 1 fA to 20 mA.
The RF ICs feature high input impedance and open-collector outputs for maximum flexibility, enabling them to be used with a variety of oscillator topologies.
Instrumentation Amplifier Applications Instrumentation amplifiers amplify small differential voltages in the presence of large common-mode voltages,while offering a high input impedance.
This design maintains the high input impedance of the FET input, but an RLC to ground can be used with amplifiers where this is not a requirement.
The±12V isolated power solution is optional andis only needed for applications that require the MAX9632 amplifiers to provide a high input impedance or when power isolation is required.
Both U1 and U2 provide high input impedance for input signals that have a large source resistance, or in the case of the 4-20mA loop, a 250Ω load resistance.
The input section includes a low-noise programmable gain amplifier(PGA)with very high input impedance and available gains from 1x to 128x to optimize the overall dynamic range.
Both channels also have high input impedance, low noise,high CMRR, programmable gain, various low-pass and high-pass filter options, and a high resolution analog-to-digital converter.
Special features include an excellent common-mode rejection ratio(CMRR),no input stage crossover distortion, high input impedance, and rail-to-rail input and output swing.
They provide high input impedance, low input bias current, low supply current, independent power-down(for multiple amplifiers in a single package), low output impedance, and low propagation delay.
Instrumentation Amplifier Directly Drives the AD4000 ADC Family The instrumentation amplifiers offer excellent precision performance,common-mode rejection, and high input impedance to interface directly with sensors, but they have usually lower small signal bandwidth<10 MHz.
Since the receiver uses high input impedance and the transmission driver has a stronger driving capability than RS232, it is allowed to connect multiple receiving nodes on the same transmission line, and up to 10 nodes can be connected.
Signal conditioning uses a range of different amplifiers for different purposes, including instrumentation amplifiers, which are optimised for use with DC signals,and are characterized by high input impedance, high common mode rejection ratio(CMRR), and high gain.
Spellman HVD 시리즈 저항 전압 디바이더 100kV,200kV and 400kV Models High Input Impedance 25ppm Temperature Coefficient Corona Free Operation 0.5% Accuracy(higher accuracies available)*Note: All specifications are subject to change without notice.
Connecting the voltmeter block 160 to the signal lines of the bus 30 in this manner does not have any practical effect on activecommunications because the voltmeter block 160 has a high input impedance(e.g., greater than one megaohm).
Additionally, the CMOS input stage allows for very low input-bias currents, low offset voltages,and very high input impedances, making these devices well suited for signal conditioning high-impedance sources, such as the photodiode preamplifier circuit shown in Figure 3.
These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage and drift,low input bias current, high input impedance, high slew rate and wide bandwidth.
Advantages of digiPOTs for Signal Amplification The circuits shown in Figure 4 andFigure 5 have high input impedance and low output impedance, and can work with unipolar and bipolar signals. digiPOTs can be used in vernier operation to provide greater resolution over a reduced range with fixed external resistors, and can be used in op-amp circuits with or without signal inversion.
Differential sensor with the highest input impedance in the industry minimizes noise to signal ratio providing superb signal detection.
Oscilloscopes generally use a higher input impedance to reduce the impact on the test circuit.