英語 での Lower data rates の使用例とその 日本語 への翻訳
{-}
- 
                        Colloquial
                    
 - 
                        Ecclesiastic
                    
 - 
                        Computer
                    
 - 
                        Programming
                    
 
In reality, however, the lower data rates normally work fine.
On2 encoder delivers better quality video at lower data rates.
Coverage(Cell Size) Lower data rates can be demodulated across greater distances than higher data rates. .
When you deliver video over the Internet, produce files at lower data rates.
Lower data rates(such as 1 Mbps) can extend farther from the AP than can higher data rates  such as 54 Mbps.
The most effective way toreduce channel utilization is to remove lower data rates.
At lower data rates, the allowed bit time is longer, so the propagation delay(and thus the cable distance) can also be longer.
When you deliver video over the Internet, produce files at lower data rates.
Enable lower data rates in order to increase the effective range of the AP; disable the lower data rates  in order to decrease the effective range of the AP.
When you perform coverage tests on 2.4 GHz,it is recommended to have the lower data rates disabled.
The lower data rates in 802.11a can be disabled, the 24 Mbps data rate  can be set to"required", while the rates  of 36 to 54 can be left enabled.
The lower  frequencies exhibit better range,but with limited bandwidth and hence lower data rates.
Lower data rates of up to 200 Mbps in combination with connectors for high data rates  and shielded wire pairs even enable cable lengths of several meters.
High Channel Utilization- In order to attempt to reduce channel utilization and improve performance,disable the lower data rates.
When you disable the lower data rates and limit the number of SSIDs, this reduces time spent on management traffic and allows for more bandwidth for the connected clients.
The use of multiple wireless communications standards in parallel in such a confinedenvironment can lead to quality problems, lower data rates or even complete failure.
At lower data rates, the high speed of the device enables it to spend most of its time in the power-down mode-the average power dissipation is less than 100 mW at 10-kHz data rate. .
Common Troubleshooting Scenarios Suspect poor coverage/not enough AP density- If AP transmit power is already at the maximum,you can enable the lower data rates to allow clients to connect from farther away.
For example, if you have voice services in the environment, you are likely to have a higher density deployment andshould disable the lower data rates to improve performance guideline for 792x is 12 Mbps as lowest. .
Note: For better connectivity, set the lowest data rate to mandatory on the WLC and other data rates  to supported.
However, they are capable of leaking sensitive information that require low data rates to communicate(e.g., text, recorded audio, cryptographic key material).
In the U.S. Department of Defense as well as in commercial industries,there are several applications that need wireless communication at low data rates(and consequently with low  power consumption).
P is the ideal format for streaming because it is HD resolution,has a 16:9 aspect ratio and also generates the lowest data rate, making streaming over the internet extremely easy while retaining incredible quality.
Based on the growth of M2M and the coming explosion of the Internet of Things(IoT),Thuraya is developing solutions to address low data rate(LDR), medium data  rate(MDR) and high data  rate(HDR) requirements for a range of market segments.
For a pin-compatible version at a lower data rate, refer to the MAX1426 data  sheet.
The use of LongWave LEDs is particularly attractive for low data rate, low power applications where cost is a critical parameter.
It enables LoT implementations mandating low data rates and battery-powered end devices over long-distance connectivity.
Picture credit: WinbondF This means that there is a considerable benefit to be gained from any technology that can reduce powerconsumption when mobile DRAM operates at low data rates.
The presence of phase noisewill raise the measured modulated spectrum for low data rates whose theoretical sidelobe power levels are more than 35dB below the carrier-lobe power when measured 500kHz from the carrier.