英語 での Operational amplifier の使用例とその 日本語 への翻訳
{-}
-
Colloquial
-
Ecclesiastic
-
Computer
-
Programming
Ideal Operational Amplifiers.
ELM824xA3.0μA Very low power CMOS dual operational amplifier.
Low-Power Operational Amplifier.
A μA741 integrated circuit, one of the most successful operational amplifiers.
Automotive Operational Amplifiers.
And beside the above, the S-19630AB has additional features whichare not included in the existing CMOS operational amplifier.
ELM832xC(20μA Low power CMOS operational amplifier) version has been upgraded.
The operational amplifier is typically configured as a TIA for both types of meters.
MODSET Voltage Calculation The output voltage from the operational amplifier shown in Figure 2 is calculated in Equation 3.
The low-power operational amplifier and comparators provide building blocks for enhanced diagnostic features.
Bob was an analog guru and he worked on the first reasonably,cost-effective, operational amplifier made for mass production.
The Maxim LMX321AXK-T operational amplifier is available in a 2.1mm x 2.0mm SC70-5 package.
Typical interface power consumption vs. capacitive load. Other typical constituents of an ADCcircuit design are a voltage reference and an operational amplifier.
The MAX9000 device family integrates a high-speed operational amplifier, a high-speed comparator, and a precision bandgap reference.
A generic operational amplifier and NPN transistor can be used; the smallest, most affordable components will perform adequately in this application.
High quality buffer circuits For the final stage of analog audio output(buffer amplifier), New JRC's high end audio operational amplifier MUSES is used.
Compact Solution Using an operational amplifier in a chip-scale package and 0201 resistors will provide the most compact solution.
We can detect the CO2 density by comparing this with the ingredient of the reference wavelength range not tobe absorbed by CO2 Related productsHigh-precision Operational Amplifier AK2920T.
S-89130/89140 Series is a CMOS type operational amplifier that has a phase compensation circuit, and operates at a low voltage with low current consumption.
The MAX9924/MAX9926 differential amplifiers provide a fixed gain of1V/V. The MAX9925/MAX9927 make all three terminals of the internal operational amplifier available, allowing greater flexibility for gain.
Because a Hall effect IC combines a Hall element and operational amplifier, the number of externally attached components can be reduced and circuit design can be simplified.
MAX9632 36V, Precision, Low-Noise, Wide-Band Amplifier- Maxim Description Create a design and simulate using EE-Sim® tools: The MAX9632 is a low-noise, precision,wide-band operational amplifier that can operate in a very wide +4.5V to +36V supply voltage range.
The operational amplifier, U1, and its components form the Sallen-Key data filter, which smoothes the output of the detected amplitude from the ASK demodulator.
MODSET current-to-voltage conversion circuit.Compact Solution Using a chip-scale packaged operational amplifier and 0201 resistors will provide the most compact solution.
For instance, if you use the S-8943(operational amplifier) as a comparator, the current consumption may increase up to 3 to 6 μA when the output is saturated on the VDD side.
MAX9633 Dual 36V Op Amp for 18-Bit SAR ADC Front-End- Maxim Description Create a design and simulate using EE-Sim® tools: The MAX9633 is a low-noise,low-distortion operational amplifier that is optimized to drive ADCs for use in applications from DC to a few MHz.
The OPA4188 operational amplifier uses TI proprietary auto-zeroing techniques to provide low offset voltage(25 μV, maximum), and near zero-drift over time and temperature.
The ultra-low supply current, low operating voltage,and rail-to-rail output capabilities make this operational amplifier ideal for use in single lithium ion(Li+), two-cell NiCd or alkaline battery systems.
The operational amplifier, U2, and its components form the data slicer comparator, while the peak-detecting operational amplifier, U3, and its components form the peak-detector output.
Figure 5. The MAX4007's response with output operational amplifier. The end application in Figure 4 is extremely small with one SOT23 device(MAX4007), an opamp in an SC70 package(MAX4412), and a few discrete components.