容差 英语是什么意思 - 英语翻译

• tolerance

在 中文 中使用 容差 的示例及其翻译为 英语

经度容差：.
Longitude tolerance:.

重量）和容差或比例范围。
(weight) and tolerance or percentage range.

纵向容差：.
Longitudinal tolerance:.

比如,电视机的设计就是容差设计。
For example, the design of TV is tolerance design.

充电时间可能因系统容差而有+/-10%的差异。
Charging time may vary +/-10% due to system tolerance.

即使暂停48小时也可能导致容差明显下降。
Even a 48-hour break can result in a noticeable lowering of tolerance.

弹性模量表现出不确定度（弹性模量容差）。
The modulus of elasticity exhibits an uncertainty(tolerance of the modulus of elasticity).

即使暂停48小时也可能导致容差明显下降。
Even a pause of 48 hours may result in a noticeable decrease in tolerance.

Abs_tol是最小绝对容差--对于接近零的比较很有用。
Abs_tol: is a minimum absolute tolerance level-- useful for comparisons near zero.

DIY或低成本设备的当前容差限制在0.1-0.2左右。
The current tolerance limit for DIY or low cost devices is around 0.1- 0.2.

打印分辨率和容差的概念经常混合，叠加甚至互换。
The concepts of print resolution and tolerance are often mixed, superimposed and even interchanged.

重点是通过设置最大容差的上边界来识别诚实节点。
The focus is on identifying honest nodes by putting an upper boundary for maximum tolerance.

然而，按摩椅通常熟练地引入触摸和缓慢地建立容差。
However, a massage chairs are usually skilled at introducing touch and slowly building tolerance for it.

如果有任何文件低于预设容差水平，则会突出显示它们以供人工审阅。
If any files are below the default tolerance level, they are highlighted for human review.

田口玄一提出了新产品设计开发的三阶段思想：系统设计、参数设计、容差设计。
Taguchi identified three phases in product design- system design, parameter design and tolerance design.

第四梯队才开始研究用容差设计和更便宜的零部件，做出最好的产品来。
The fourth tier team began to study tolerance design and cheaper parts to make the best products.

大多数电阻器制造商规定了一个独立于容差规格说明的温度系数。
Most resistor manufacturers specify a temperature coefficient that is separate from the tolerance specification.

这种容差表现为原有的形态和您导出的STL网格之间的最大距离。
This tolerance is defined as the maximum distance between the original shape and the STL mesh you are exporting.

通过VAST，操作员可以检查更广泛的特征容差，包括形状，大小和位置。
With Vast, operators are able to check a wider range of feature tolerances including form, size and location.

最后，它具有广泛的元数据字段，包括名称，作者，公司，描述，数量，容差等。
Finally, it has extensive metadata fields including name, author, company, description, volume, tolerances, and much more.

CQI-9中的工艺表列出了针对特定工艺的最小容差要求（参见CQI-9中附录）。
Within CQI-9 the process tables indicate the minimum tolerance requirements for specific processes(see appendices within CQI-9).

这并不容易，因为电路必须可调节，以补偿各种相位延迟，并且会随温度、元件容差而变化。
This is not trivial, because the circuit must be adjustable to compensate for different phase delays, and will vary with temperature and component tolerance.

可以将它们视为不同概念的一个很好的证据是，印刷容差通常表现出比分辨率更不利的值。
A good proof that they can be taken as different concepts is that printing tolerance often presents values that are more unfavorable than resolution.

另外一个缺陷是尽管容差范围很窄，不同元件在电气特征方面还是略有差别。
A further drawback is the fact that despite a narrow tolerance, the individual components differ slightly from each other in their electrical characteristics.

在评估分布式数据系统时，您必须考虑CAP定理-您可以select以下两项：一致性，可用性和分区容差。
When evaluating distributed data systems, you have to consider the CAP theorem- you can pick two of the following: consistency, availability, and partition tolerance.

软件还持续监控哪些吊装点处于最高和最低位置以及它们是否仍在设定的容差范围内。
The software also constantly monitors which lifting points are in the highest and lowest positions and whether these are still within the set tolerances.