模量 英语是什么意思 - 英语翻译

• modulus

在 中文 中使用 模量 的示例及其翻译为 英语

其强度和模量都不是最优。
The size and style are not our best.

模量大于450GPa的称为超高模子。
The modulus is larger than 450GPa called the Hyper model.

钛合金的弹性模量约为钢的1/2。
The modulus of elasticity of titanium alloy is about 1/2 of that of steel.

模量大于450GPa的称为超高模型。
The modulus is greater than 450GPa, called the ultra-high model.

铬的弹性模量也低于钼和钨。
Chromium's modulus of elasticity is also lower than that of molybdenum and tungsten.

模量大于450GPa的称为超高模子。
The modulus is greater than 450GPa, called the ultra-high model.

钛螺丝的弹性模量在常温时为106.4GMPa,为钢的57%。
The modulus of elasticity of titanium at room temperature is 106.4GMPa, 57% of steel.

弹性模量324GPa，提高10%，正进入产业化阶段。
Modulus of elasticity 324GPa, 10%, is entering the stage of industrialization.

钛螺丝的弹性模量在常温时为106.4GMPa,为钢的57%。
The modulus of elasticity of titanium is 106.4 GMPa at room temperature, which is only 57% of steel.

在极坐标中，一个复数z由模量r和相位角phi来定义。
In polar coordinates, a complex number z is defined by the modulus r and the phase angle phi.

弹性模量：材料的弹性模量随着氢含量的增加而降低;
(1) Modulus of elasticity- the elastic modulus of a material decreases as the hydrogen content increases;

(3)橡胶减振器弹性模量比金属小得多，可产生较大弹性形变;
(3) The modulus of elasticity is much smaller than that of metal, which can produce a large elastic deformation;

在实验室中精确地测定弹性模量是非常昂贵的，而且往往无法实现。
Accurately determining the modulus of elasticity in a suitable laboratory is costly and often cannot be implemented.

FRP的弹性模量是木材的两倍，但比钢小10倍（E=2.1×105）。
The modulus of elasticity of FRP is twice as large as that of wood, but 10 times smaller than that of steel(E=2.1*105).

在104GPa、室温条件下，铌的弹性模量低于钨、钼或钽。
At 104 GPa at room temperature, the modulus of elasticity of niobium is less than that of tungsten, molybdenum or tantalum.

当温度在300～400℃之间时，钢的强度和弹性模量显著降低。
When the temperature is between 300° C and 400° C, the strength and elastic modulus of the steel are significantly reduced.

弯曲模量-可以弯曲多少材料而不会损坏，并且仍然能够恢复原始形状。
Flexural Modulus- how much a material can be bent without being damaged and is still able to return to the original shape.

当温度在300°C到400°C之间时，钢的强度和弹性模量相对降低。
When the temperature is between 300° C and 400° C, the strength and elastic modulus of the steel are significantly reduced.

最初，测试样品的厚度使用卡尺来测量(用于在模量计算中)。
Initially, the thickness of the test sample is measured using calipers(for use in the modulus calculations).

物理性能如拉伸强度、冲击强度、伸长率和模量可能在诱导期内引起变化；.
Physical properties, such as tensile and impact strength and elongation and modulus, sometimes change during this induction period;

弹性模量低：钛的弹性模量在常温时为106.4GMPa，为钢的57%。
Low modulus of elasticity: The modulus of elasticity of titanium is 106.4 GMPa at room temperature, which is 57% of steel.

根据GB1239，当普通盘簧工作温度超过60℃时，应修正剪切模量。
According to the provisions of GB1239, when the working temperature of common coil springs exceeds 60°C, the shear modulus should be corrected.

细度模量的典型值从大约2.3到3.1不等,前者包括更多的细颗粒和后者的粗颗粒。
Typical values for the fineness modulus range from about 2.3 to 3.1, with the former consisting more of fine particles and the latter of coarser particles.

最初的Montefibre80K产品系列包括M500和M600，两者均用于非航空航天用途，具有标准模量（SM）。
The initial Montefibre 80k product range will reportedly consist of the M500 and M600 for non-aerospace use, with standard modulus(SM).

注意，弹性模量的TC本身与温度有关，这意味着这种效应永远无法完全补偿。
Note that the TC of the modulus of elasticity is itself temperature-dependent, which means that this effect can never be entirely compensated for.

除了工厂产能增大之外，一些公司正在研发先进玻璃纤维，其趋势是提高拉伸强度、模量和耐热性。
Apart from plant capacity expansion, numerous companies are developing advanced glass fibers, with a trend toward increased tensile strength, modulus and temperature resistance.

弹性模量（制造商参数规格）显示一定的不确定性（弹性模量公差），可能为百分之几。
The modulus of elasticity(manufacturer specification) exhibits an uncertainty(tolerance of the modulus of elasticity) which may be several percent.

加入增塑剂可以降低熔体粘度、玻璃化转变温度和产品的弹性模量而不会改变被增塑材料的基本化学性质。
Adding plasticizer can reduce the melt viscosity, glass temperature and elastic modulus of the elastomer without changing the basic chemical properties of the plasticized material.

添加增塑剂可以降低塑料的熔融粘度，玻璃化转变温度和弹性体的弹性模量，而不会改变塑化材料的基本化学性质.
Adding plasticizer can reduce the melt viscosity, glass temperature and elastic modulus of the elastomer without changing the basic chemical properties of the plasticized material.