What is the translation of " 串行数据 " in English?

• serial data

Examples of using 串行数据 in Chinese and their translations into English

可以通过串行数据控制1/2偏置和1/3偏置驱动方案。
Bias and 1/3 bias drive schemes can be controlled from serial data.

然后主设备发送一个或多个串行数据字节。
The master then transmits one or more bytes of serial data.

数字引脚也是串行数据传输器的基础，通过单个数字输出可以发送多个命令（如清单1-2所示）。
Digital pins are also the basis for serial data transfer, which can send multiple commands through a single digital output(Listing 1-2).

进行串行数据传输时，FSYNC引脚必须置低，要注意FSYNC有效到SCLK下降沿的建立时间t7的最小值。
To start the serial data transfer, FSYNC should be taken low, observing the minimum FSYNC-to-SCLK falling edge setup time, t7.

串行数据传输总是以起始条件开始并以停止条件结束。
Serial data transfer always begins with a start condition and ends with a stop condition.

其中一间拥有专为IQ总线串行数据环路设计的模拟光纤收发器的公司就是FiberOptions。
One company that does have an analog fiber transceiver designed specifically for the IQ Bus serial data loop is Fiber Options.

串行数据采集工具允许您查看您感兴趣的特定参数，而无需涉及不必要的数据。
The serial data acquisition tool allows you to view the specific parameters you are interested in without the need to wade through unnecessary data..

要开始记录串行数据，你只需要下载应用程序，你会看到所有的活动通过你的RS232端口。
To start logging serial data, you just need to download the application, and you will see all the activity going over your RS232 port.

MIL-STD-1553是美国国防部发布的一个军用标准，定义了机械、电气和串行数据总线的功能特征。
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus.

用于接收（RX）和发送（TX）TTL串行数据。
Used to receive(RX) and transmit(TX) TTL serial data.

用于接收（RX）和发送（TX）TTL串行数据。
They are used to receive(RX) and transmit(TX) TTL serial data.

如此，SerialtoEthernetConnector将允许您与数百个物理位于数英里的设备交换串行数据。
That way, Serial to Ethernet Connector will allow you to exchange serial data with hundreds of devices physically located miles away.

用于接收（RX）和发送（TX）TTL串行数据（3.3V级）。
Used to receive(RX) and transmit(TX) TTL serial data(with 3.3 V level).

那么，如果您需要，可以使用这两个引脚向PC发送串行数据。
And so these two pins would allow us, if you wanted to, to send serial data to the PC.

UART/ACE将计算机内部并行总线转换为串行数据流。
The UART/ACE converts the internal parallel bus of the computer into a serial data stream.

显示我们记录的数据的第一项任务是从Arduino获取串行数据。
The first task in displaying our recorded data is to obtain the serial data from the Arduino.

UART0有两个相关的SFR：串行控制寄存器0(SCON0)和串行数据缓冲器0(SBUF0)。
UART0 has two associated SFRs: Serial Control Register 0(SCON0) and Serial Data Buffer 0(SBUF0).

NetBurner串口转以太网服务器是一种紧凑的硬件设备，可以轻松地将串行数据转换为以太网信号，反之亦然。
NetBurner Serial to Ethernet Server is a compact hardware device that can easily convert serial data into Ethernet signals and vice versa.

串口（Serial）：0（RX）和1（TX）用于接收（RX）和发送（TX）TTL串行数据。
Serial: 0(RX) and 1(TX)- Used to receive(RX) and transmit(TX) TTL serial data.

波特率-GPS接收器以特定比特率从发送引脚（TX）发送串行数据。
Baud Rate- GPS receivers send serial data out of a transmit pin(TX) at a specific bit rate.

串行数据传输速度更高，仅受计算机性能和网络速度的限制.
Higher transmission speed of serial data, limited only by computer performance and network speed.

在大多数情况下移动到或来自计算机的数据作为串行数据移动。
Data moving to or from a computer, in most cases, moves as serial data.

AD9854支持10MHz串行通信方式和100MHz并行通信方式，本系统采用串行数据输入方式。
AD9854 supports 10 MHz and 100 MHz serial communication parallel communication mode, the system uses the serial data input.

I²C为2线、低速率、串行数据连接IC总线，用于集成电路之间的信号传输，通常是在同一电路板上。
I²C is a two-wire, low-speed, serial data connection IC bus used to run signals between integrated circuits, generally on the same board.

RS-232串行数据包由1个起始位、5至8个数据位、1/1.5/2个停止位和1个奇偶校验位组成（图2）。
The RS-232 serial data packet consists of a start bit, anywhere from 5 to 8 data bits, 1/1.5/2 stop bits, and a parity bit(Figure 2).

串行数据，先发送MSB。
Data is transmitted MSB first.

模式0：串行数据通过RXD进出。
Mode 0: Serial data enters and exits through RXD.

并行数据传输比串行数据传输更快。
Serial data transfers are faster than parallel transfers.

FireWire或IEEE1394是串行数据传输的总线标准。
FireWire or IEEE1394 is a bus standard for serial data transmission.

了解如何利用光纤链路轻松传输JESD204高速串行数据。
Find out how easy it is to transfer JESD204 high speed serial data over a fiber-optic link.