Examples of using Serial data in English and their translations into Chinese
{-}
-
Political
-
Ecclesiastic
-
Programming
Advanced Serial Data Logger.
Used to receive(RX) and transmit(TX) TTL serial data.
用于接收（RX）和发送（TX）TTL串行数据。The serial data is abnormal.
Abnormal大数据是异常的。They are used to receive(RX) and transmit(TX) TTL serial data.
用于接收（RX）和发送（TX）TTL串行数据。Serial data transfer always begins with a start condition and ends with a stop condition.
串行数据传输总是以起始条件开始并以停止条件结束。GP1(Pin 6, O/P): This will be used for serial data transfer to a PC.
GP1的(6脚，O/P)：这将是用于串行数据传输到PC。If the received serial data is larger than 1KB, it will automatically packaged as Ethernet packets and sent to the Ethernet port.
如果接收到的串行数据大于1KB，它将自动打包为以太网数据包并发送到以太网端口。Used to receive(RX) and transmit(TX) TTL serial data(with 3.3 V level).
用于接收（RX）和发送（TX）TTL串行数据（3.3V级）。To start logging serial data, you just need to download the application, and you will see all the activity going over your RS232 port.
要开始记录串行数据，你只需要下载应用程序，你会看到所有的活动通过你的RS232端口。Serial: 0(RX) and 1(TX)--Used to transmit and receive TTL serial data.
Serial：0（RX）、1（TX），被用于接收和发送串口数据。Baud Rate- GPS receivers send serial data out of a transmit pin(TX) at a specific bit rate.
波特率-GPS接收器以特定比特率从发送引脚（TX）发送串行数据。And so these two pins would allow us, if you wanted to, to send serial data to the PC.
那么，如果您需要，可以使用这两个引脚向PC发送串行数据。To start the serial data transfer, FSYNC should be taken low, observing the minimum FSYNC-to-SCLK falling edge setup time, t7.
进行串行数据传输时，FSYNC引脚必须置低，要注意FSYNC有效到SCLK下降沿的建立时间t7的最小值。The UART/ACE converts the internal parallel bus of the computer into a serial data stream.
UART/ACE将计算机内部并行总线转换为串行数据流。Digital pins are also the basis for serial data transfer, which can send multiple commands through a single digital output(Listing 1-2).
数字引脚也是串行数据传输器的基础，通过单个数字输出可以发送多个命令（如清单1-2所示）。串口（Serial）：0（RX）和1（TX）用于接收（RX）和发送（TX）TTL串行数据。Captured serial data can be displayed in various formats, and the opportunity of real-time monitoring is a great feature for problem resolution.
捕获的串行数据可以以各种格式显示，实时监控的机会是解决问题的一个很好的功能。The first task indisplaying our recorded data is to obtain the serial data from the Arduino.
显示我们记录的数据的第一项任务是从Arduino获取串行数据。I²C is a two-wire, low-speed, serial data connection IC bus used to run signals between integrated circuits, generally on the same board.
I²C为2线、低速率、串行数据连接IC总线，用于集成电路之间的信号传输，通常是在同一电路板上。The device is aimed at creating a network connection andtransferring serial data it receives via a COM port to LAN.
该设备旨在创建网络连接并将通过COM端口接收的串行数据传输到LAN。Inter-integrated circuit(I2C) is a system for serial data exchange between the microcontrollers and specialized integrated circuits of a new generation.
内部集成电路（I2C）是用于微控制器和新一代专用集成电路之间的串行数据交换系统。UART0 has two associated SFRs:Serial Control Register 0(SCON0) and Serial Data Buffer 0(SBUF0).
UART0有两个相关的SFR：串行控制寄存器0(SCON0)和串行数据缓冲器0(SBUF0)。The serial data acquisition tool allows you to view the specific parameters you are interested in without the need to wade through unnecessary data. .
串行数据采集工具允许您查看您感兴趣的特定参数，而无需涉及不必要的数据。One company that does have an analog fibertransceiver designed specifically for the IQ Bus serial data loop is Fiber Options.
其中一间拥有专为IQ总线串行数据环路设计的模拟光纤收发器的公司就是FiberOptions。The three new ISL7202xSEH CAN transceivers provide reliable serial data transmission between a CAN controller and CAN bus at speeds up to 1 Mbps.
Intersil的ISL7202xSEH系列CAN收发器可在CAN控制器和CAN总线之间以最高1Mbps的速度提供可靠的串行数据传输.Once USB communications are established, the EVAL-SDP-CS1Z can now be used to send, receive,and capture serial data from the EVAL-CN0274-SDPZ.
一旦USB通信建立，就可以使用EVAL-SDP-CS1Z来发送、接收和捕捉来自EVAL-CN0274-SDPZ的串行数据。That way,Serial to Ethernet Connector will allow you to exchange serial data with hundreds of devices physically located miles away.
如此，SerialtoEthernetConnector将允许您与数百个物理位于数英里的设备交换串行数据。MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical,and functional characteristics of a serial data bus.
MIL-STD-1553是美国国防部发布的一个军用标准，定义了机械、电气和串行数据总线的功能特征。SerialPortMonitor专注于捕获，记录和显示通过系统RS-485端口传输的串行数据。NetBurner Serial to Ethernet Server is a compacthardware device that can easily convert serial data into Ethernet signals and vice versa.
NetBurner串口转以太网服务器是一种紧凑的硬件设备，可以轻松地将串行数据转换为以太网信号，反之亦然。
