Examples of using Mpa in English and their translations into Chinese
{-}
-
Political
-
Ecclesiastic
-
Programming
Why the mpa?
为什么是MPA?MPa clean and stable air source.
空气源0.6Mpa稳定，清洁的压缩空气.Tensile strength= 420 MPa(+- 20% variation).
Maximum working pressure equal to or greater than 69 MPa;
最大工作压力等于或大于69兆帕；.MPa correspond to a force of 1.2 tons on the surface of a one Euro cent coin.
MPa的强度，相当于在一枚1欧分硬币表面上施加1.2吨的力。(c) Capable of producing an ultimate vacuum better than 13.3 mPa.
(c)能产生超过13.3兆帕的极度真空。Viscosity(25oC, mpa. s): 25~100000(can be customized according to user requirements).
粘度(25ºC,mpa.s):25～100000(可根据用户要求定制)。In the 19th century,the usual steam pressure increased to about 0.8 MPa.
世纪，常用的蒸汽压力提高到0.8兆帕左右。Viscosity(25oC, mpa. s): 25~100000(can be customized according to user requirements).
粘度(25oC,mpa.s):25～100000(可根据用户要求定制)。The opening pressure of the burstingdisc shall amount to 250 bar(25 MPa).
防爆盘的破裂压力须达250巴(25兆帕)。At 10 wt% of CNTs thestress value obtained reached 2.55 MPa which is 9 times that of pure natural rubber.
在10wt%CNTs得到的重点值到达了2.55是9次纯天然橡胶的MPa。With the hardness tester test results should be the base layer of thesurface hardness of not less than 1.2 MPa.
用硬度测试仪检测结果应是基层的表面硬度不低于1.2兆帕.MPa, at the same time temperature up to 750- 1000K and the gasoline engine at this time of the mixed gas pressure will be 0.
MPa，同时温度高达750-1000K（而汽油机在此时的混合气压力会为0。For example, concrete with a strength class of C30 means 30 MPa≤ fcu< 35 MPa.
例如，强度等级为C30的混凝土是指30MPa≤fcu<35MPa.High-strength aluminum alloy tensile strength greater than 480 MPa, fully meet the intensity of high-speed rail train car standards.
高强度的铝合金抗拉强度大于480兆帕，完全能契合高铁列车车厢的强度标准。(d) The bursting pressure as determined by quasi-static load through an incompressible fluid shall be 30+-3 MPa.".
通过不可压缩的流体以准静态加载确定的爆破压力，应为30+-3兆帕"。It boosts the pressure of the liquidhydrogen from 30 to 276 psia(0.2 to 1.9 MPa) and supplies it to the high-pressure fuel turbopump(HPFTP).
它将液氢的压力从0.2兆帕增加到1.9兆帕，并将之供给高压燃料涡轮泵（HPFTP）。In terms of system protection, the high pressure switch setting is adjusted from the original 2.45 MPa to 2.7 MPa.
在系统保护方面，高压开关的设定值从原来的2.45兆帕调整到2.7兆帕.For example, the tensile strength per unit mass of alloy steel is 160 MPa, while plastic reinforced with glass fiber can reach 170~ 400 MPa.
例如，合金钢的单位质量的抗拉强度为160mpa，而用玻璃纤维增强的塑料可以达到170~400mpa。The piping and valves which are fitted directly to the test vessel,shall be pressure resistant up to 500 bar(50 MPa).
直接装在试验容器上的蜂鸣器和阀门，耐压必须达到500巴(50兆帕)。So in the Allam cycle, the CO2 is compressed to a superfluid at around 8 MPa, cooled, and then efficiently pumped to 30 MPa.
所以在阿拉姆循环中，二氧化碳被压缩成为8兆帕左右的超流体，随后冷却，然后高效泵送到30兆帕。Pressures is the first application that connects 4 more frequently used units of pressure measurement: bar,atm, MPa and psi.
压力，这是第一个应用程序连接4黑莓常用压力计量单位：条，ATM，PSI和兆帕。At room temperature, for example, it achieves a compression shear strength of 65 MPa on aluminum and 55 MPa on ceramics.
在室温条件下，它在铝上的压缩剪切强度达到65MPa，在陶瓷上达到55MPa。According to recent foreign data, the intensity threshold of hydrogen brittle fracture in automotivehardware fasteners may drop to 1000 MPa.
从国外资料看，汽车紧固件发生氢脆断裂的强度阈值可能会下降到1000MPa。The now highly pure CO2 stream is then compressed, cooled,and pumped up to a supercritical 30 MPa for a return trip to the combustor.
然后高度纯净的二氧化碳流被压缩、冷却，泵送到30兆帕，进入超临界状态，返回燃烧室。The mold can then be closed and the molten metal injected at high pressure,with a pressure range of about 10 to 175 mpa.
然后就可以关闭模具，用高压将熔融金属注射进模具内，这个压力范围大约在10到175兆帕之间。By the 1980s, the oxygen production capacity of large air separation equipment had reached 70,000 meters/ time;Air pressure drops to 0.36 mpa;
到80年代，大型空气分离设备的氧气生产能力已达到70000米空气压力下降到0.36兆帕;For tanks not more than test pressure of the tank(according to 4.2.1.13.4 tank shall be designed for atest pressure of at least 0.4 MPa).
对于罐体，不超过罐体的试验压力(根据4.2.1.13.4,罐体设计的试验压力至少为0.4兆帕)，.Gas cylinders- Refillable seamless steel gas cylinders- Design, construction and testing- Part 1: Quenched andtempered steel cylinders with tensile strength less than 1100 Mpa.
气瓶－可再充装无缝钢气瓶－设计、制造和试验－第1部分：抗拉强度小于1100兆帕的调质钢气瓶.
