Examples of using Reference temperature in English and their translations into Greek
{-}
-
Colloquial
-
Official
-
Medicine
-
Ecclesiastic
-
Financial
-
Official/political
-
Computer
The reference temperature is 30ºC.
Clock Error≤0.5sec/ per day( reference temperature);
T0 is the reference temperature, normally 25°C.
We can offer PTC thermistor for over-current protection with reference temperature 80℃, 100℃, 120℃, 140℃.
Performance reference temperature/degree.
Reference temperature for setting of thermal element.
The rated current(non-trip current)depends on reference temperature and ceramic body diameter.
The reference temperature and pressure for the above table are 20 °C and 1 atmosphere(101.325 kPa).
Overfilling or overpressurisation having regard in particular to the filling ratio andto vapour pressure at the reference temperature.
Selection of Reference temperature(also called Switch temperature or Curie temperature). .
Between -25℃ to +60℃,clock accuracy is no more than±1 s/d; Under reference temperature 23℃, clock accuracy is no more than±0.5 s/d.
The reference temperature is 20 °C unless otherwise specified by the manufacturer and marked on the measure accordingly.
Materials used for material measures shall be such that length variations due to temperature excursions up to± 8 °C about the reference temperature do not exceed the MPE.
In consideration of cutting down cost,high reference temperature and small dimension PTC Thermistor current limiting devices shall be more economical, but it may leads to higher PTC thermistor surface temperature, and need to check whether it will cause undesired unfavorable effects.
Maximum operating voltage 265V, rated zero power resistance at 25C(R25) 15 Ω±20%, non-trip current 140mA,trip current 350 mA, maximum current 1.5A, reference temperature 120℃, diameter 11mm.
Maximum ambient temperature in PTC thermistor protector installation position may reach 60℃, reference temperature should be 40℃ higher than that, then the reference temperature can be 100℃.
Wilhelm Carl Wien(1864- 1928) was a German physicist who, in 1893, used theories about heat andelectromagnetism to deduce Wien's displacement law, which calculates the emission of a blackbody at any temperature from the emission at any one reference temperature.
In case the drcuit breaker operates at higher temperatures than +40°C, the current-carrying capacity of the circuit breaker may be lower than the rated current-carry capacity at the reference temperature, therefore the derating coeffrcients must be applied, see the derating coeffictents table on page A/00.
Wilhelm Carl Werner Otto Fritz Franz Wien(German:; 13 January 1864- 30 August 1928) was a German physicist who, in 1893, used theories about heat and electromagnetism to deduce Wien's displacement law,which calculates the emission of a blackbody at any temperature from the emission at any one reference temperature.
In considering cutting down cost, also PTC thermistor is not installed in the transformer windings coil, higher surface temperature won't have unfavorable effect to transformer,therefore reference temperature can also be 120℃, and then the diameter of PTC Thermistor can be smaller.
Performance guarantee range:+ 5℃~+ 25℃(cooling time and minimum temperature reference 1~6).
Previously natural gas quantities were allocated in MWh(0 oC, reference combustion temperature).
Δθ= deviation of ambient temperature from the reference operating condition.
Reference design temperature'(Tdesignh) means the outdoor temperature, expressed in degrees Celsius, as set out in Annex VII, Table 10, at which the part load ratio is equal to 1;
Following the entry into force of the 3rd amendment of the Gas Network Code(1/6/2017)natural gas quantities imported in Greece are allocated daily by the Greek TSO DESFA in kWh(25 oC, reference combustion temperature).
The Forecast GCV is expressed in MWh/NM3(reference combustion temperature 0oC) and is converted in MWh/ SM3(reference combustion temperature 25oC) by using the applicable conversion factors listed in ISO 13443 in force.
This temperature at 32.384 °C, corresponding to the release of crystal water and melting of the hydrated salt,serves as an accurate temperature reference for thermometer calibration.
Testosterone is used as the baseline reference by which all other anabolic steroids are measured against and compared to(much like how the Celsius temperature scale utilizes the boiling andfreezing point of water as the base reference for temperature measurement).