Examples of using Psi in English and their translations into Malay
{-}
-
Colloquial
-
Ecclesiastic
-
Computer
Psi Flanged Gate Valves.
He is very interested in psi.
Psi is only one of them.”.
Investigating officer, PSI Milind Kasle.
Tensile Strength: 100,000 to 180,000 psi.
Good test. We still got 1,400 PSI on the drill line.
The maximum pressure that thisitem can reach is 70 PSI.
A PSI reading of between 101 and 200 falls in the Unhealthy range.
The sprinkler is pressurized with 5 psi of air pressure.
And if you look at the part of the circumference of the circle that's inside of it,that is the arc that is subtended by psi.
What I'm going to prove in this video is that psi is always going to be equal to 1/2 of theta.
Whatever psi is or whatever theta is, psi's going to be 1/2 of that, or whatever psi is, theta is going to be 2 times that.
Now, we know from the earlier part of this video that psi 2 is going to be equal to 1/2 theta 2, right?
Tires naturally lose 1-2 psi per month, so ongoing neglect will eventually result in a tire that cannot support the weight of the vehicle and the occupants.
If we draw a diameter just like that, if we define this angle as psi 1, that angle as psi 2.
Mild, Inflatable, Portable, 1.5 ATA or 7 psi chambers are actually Gamow Bags and do not meet the standards of a traditional chamber.
Spring-loaded hydraulic accumulators are small, lightweight devices that are suitable for mobile applications with low volumes andpressures below 500 psi.
Data obtained from the Japanese surveys found that 8 psi(55 kPa) was sufficient to destroy all wooden and brick residential structures.
In fact, hydrazine hydrate 80 is the best material that can be used for protection against oxidation in supercritical boilers operating at pressures up to 3500 psi.
So we get psi-- this psi plus that psi plus psi plus this angle, which is 180 minus theta plus 180 minus theta. These three angles must add up to 180 degrees.
We immediately you know that, just using the result I just got, since we have one side of our angles in both cases being a diameter now,we know that psi 1 is going to be equal to 1/2 theta 1.
Military planners prefer to maximise the range at which 10 psi, or more, is extended over when attacking countervalue targets, thus a 220 m height of burst would be preferred for a 1 kiloton blast.
But I think many of us when we see a triangle that looks like this, if I told you this is r and that is r, that these two sides are equal, and if this is psi, then you would also know that this angle is also going to be psi.
So psi, which is psi 1 plus psi 2, so psi 1 plus psi 2 is going to be equal to these two things. 1/2 theta 1 plus 1/2 theta 2. psi 1 plus psi 2, this is equal to the first inscribed angle that we want to deal with, just regular psi.
Hot selling product durostone sheet In addition because of its easy processing high intensity and distortion characteristics suitable for processing a variety ofdifferent structures the bending strength up to 20000 psi at the same time keep bending….
In a typical air burst, where the blast range is maximized to produce the greatest range of severe damage,i.e. the greatest range that~10 psi(69 kPa) of pressure is extended over, is a GR/ground range of 0.4 km for 1 kiloton(kt) of TNT yield; 1.9 km for 100 kt; and 8.6 km for 10 megatons(Mt) of TNT.
Hot selling product durostone sheet In addition because of its easy processing high intensity and distortion characteristics suitable for processing a variety of different structures the bending strength up to 20000 psi at the same time keep bending….
At a pressure of 1 bar or approximately 15 psi(pounds per square inch) above the existing atmospheric pressure, water in a pressure cooker will reach a temperature of 121 °C(250 °F). The boiling temperature of water(and water-based liquids) is determined by the ambient atmospheric pressure. Pressure cookers always require liquid in order to cook food under pressure.
Hot selling product Durostone Sheet, In addition, because of its easy processing, high intensity and distortion characteristics, suitable for processing a variety of different structures, the bending strength up to 20000 psi, at the same time keep bending strength in heat/temperature up to 15000 psi.