What is the translation of " THE INJECTOR " in Slovenian?

• injektor
• injektorja

Examples of using The injector in English and their translations into Slovenian

Give me the injector.
Daj mi brizgalko.

The injector assembly has separated.
Injektor se je ločil.

I need the injector.
Potrebujem brizgalec.

The injector is not working well.
Vtičnik ne deluje dobro.

Careful with the injector.
Pazljivo z vpenjačem.

The injector performs perfectly in every simulation.
Injektor deluje v vsaki simulaciji.

I'm going to launch the injector.
Izstrelil bom injektor.

Check the injector shield is fully extended.
Preverite, ali je zaščita injektorja povsem razširjena.

You might also want to inspect the injector.
Lahko probaš tudi poslušat injektorje.

If you launch the injector, the Federation will pursue you.
Če izstreliš injektor, te bo Federacija preganjala.

There are a couple of words about the injector version.
Obstaja nekaj besed o različici injektorja.

The tube from the injector to the patient(patient's tube) must be changed after every examination.
Cev od injektorja do bolnika je treba zamenjati po vsakem pregledu.

It's gotten worse. I can't get the injector valves closed.
Še slabše je, ne morem zapreti ventilov ubrizgalcev.

The injector is also simpler and more reliable because its construction is less complex and it has 40% less components.
Injektor je tudi bolj enostaven in zanesljiv, saj je konstrukcijsko manj zapleten in ima za 40% manj sestavnih delov.

The amount of fuel supplied is controlled by the time it takes to open the injector itself- everything is simple.
Količina dobavljenega goriva je odvisna od časa, potrebnega za odpiranje injektorja- vse je preprosto.

The injector injects the sample into the continuously flowing mobile phase stream that carries the sample to the HPLC column.
Injektor uvaja vzorec v neprekinjeno teče mobilno fazo toka, ki nosi vzorec v HPLC kolono.

The serum needs to be delivered directly into the brain stem, so… the injector… needs to be placed at the base of the skull.
Serum mora naravnost v možgansko deblo… Zato morate samoinjektor postaviti na dno lobanje.

When the injector is removed, the working piston is lowered downwards to prevent the working piston from being damaged due to sliding.
Ko je injektor odstranjen, se delovni bat spusti navzdol, da se prepreči poškodovanje delovnega bata zaradi drsenja.

When the pilot light you see yellow-red is not sustainable, small flame, it is necessary to purge the injector and igniter tube that brings gas.
Ko se kontrolna lučka vidite rumeno-rdeče ni trajnostno, majhen plamen, je potrebno, da očistite injektorja in vžigalno cev, ki prinaša plin.

Having dealt with the main design parts of the injector, proceed to the next question, what does the injector do, how does it work?
Ko ste se ukvarjali z glavnimi oblikovalskimi deli injektorja, nadaljujte z naslednjim vprašanjem, kako deluje injektor, kako deluje?

The injectors of lubrication pump DDB-10, DDB-18, DDB-36 will be able to close if some are not put into operation temporarily, just adjusting the feeding volume of injector to zero, or screw out the injector and sealed it with threaded plug.
Injektorji mazalne črpalke DDB-10, DDB-18, DDB-36 se bodo lahko zaprli, če nekateri začasno ne bodo začeli obratovati, samo nastavite količino vbrizgavanja injektorja na nič, ali pa privijte injektor in ga zaprite z navojem vtič.

In 2003, the engineers carried out upgrades, after which the injector power unit with 140 horsepower and the turbodiesel of the Gorky Automobile Plant"5601" were used in production.
V letu 2003 so inženirji izvedli nadgradnje, nato pa so v proizvodnji uporabljali injektorsko enoto s 140 konjskimi močmi in turbodizelom avtomobilske tovarne Gorky"5601".

The Amajet system draws in waste water from the deepest point in the stormwater tank, mixes it with air in the injector and then discharges it at high speed in a horizontal jet across the tank floor.
Sistem Amajet zajame odpadno vodo z najnižje točke bazena za padavinsko vodo, jo premeša z zrakom v injektorju in nato brizgne v horizontalnem curku z veliko hitrostjo prek tal bazena.

Pulling out the piston about 30mm before installing the injector, horizontal put on the installation of screw holes, and then work up the piston about 30 degree angle, so that the working piston end should be on the groove of the wheel exactly, then tightening hexagon nut again.
Potegnite bat okoli 30mm pred namestitvijo injektorja, vodoravno namestite vijačne luknje in nato delajte bati glede na stopnjo kota 30, tako da mora biti konec delovnega bata točno na utoru kolesa, nato pa zategnite šestero spet.

Car injector. As an injector, this is an electronic system, that means, apart from the actuator itself( the injector), the car will be stuffed with special sensors to bring everything into one tuned fuel delivery mechanism to the engine.
Kot injektor, elektronski sistem, nato pa ločeno od pogona( injektorja), avto bo pakiran s posebnimi senzorji, ki se vsem zmanjša na eno naoljen stroj dovod goriva v motor.

And the answer is quite simple, because the injector is a special system of electronic fuel injection in a car, which is a jet pump( in the form of an injector)..
Odgovor je precej preprost, saj je injektor poseben sistem elektronskega vbrizgavanja goriva v avtomobilu, ki je jet črpalka( v obliki injektorja).

The process is quite simple, like carburetor fuel input to the engine, but to calculate the correct proportion, the amount of fuel in the injector system is a special processor that processes the signal from a large number of sensors, such as: air temperature sensor, engine speed, throttle sensorflaps, the air content sensor in the mixture.
Postopek je dokaj preprost, kot vhodni uplinjač gorivo je v motorju, ampak, da bi izračunali pravilno razmerje, količino goriva v sistemu za vbrizgavanje je poseben procesor, ki obdela signal iz serije senzorjev, kot so temperature senzor, število vrtljajev motorja, senzor za plinlopute, senzor vsebnosti zraka v mešanici.

First remove the grease supply line before removing the injector, then loosen the hexagon nut to remove the injector, the grease supply piston of the injector should be tilted upward by about 30 degrees.
Najprej odstranite napajalno linijo za mast, preden odstranite injektor, nato pa sprostite šesterokotno matico, da odstranite injektor. Moč napajalnega bata injektorja je treba nagniti navzgor za približno 30 stopinj.