The program will begin working after your computer is restarted.
Het programma zal beginnen te werken nadat uw computer opnieuw is opgestart.
Suppose when the computer is restarted, the RAID controller reports an error.
Stel dat de RAID-controller een fout aangeeft nadat de computer opnieuw is gestart.
SQL Server 2008 cannot be installed until your computer is restarted.
SQL Server 2008 kan pas worden geïnstalleerd nadat uw computer opnieuw is opgestart.
Now when the computer is restarted, for your surprise the image files that you were working on Mac is missing now.
Nu wanneer de computer opnieuw wordt opgestart, voor uw verbazing de beeldbestanden die u werkte Mac ontbreekt geenw.
Mylar will now be started automatically when the computer is restarted.
Mylar wordt nu automatisch gestart, als de computer opnieuw wordt opgestart.
After performing these steps, the computer is restarted and try to turn on the device.
Nadat u deze stappen hebt uitgevoerd, wordt de computer opnieuw opgestart en probeert u het apparaat in te schakelen.
After determining the new value, the USB flash drive is removed, and then the computer is restarted.
Nadat de nieuwe waarde is bepaald, wordt de USB-stick verwijderd en wordt de computer opnieuw opgestart.
So if you wish that the changes should still present when the computer is restarted, you have to disable Deep Freeze application
Dus als je wilt dat de veranderingen moet nog steeds aanwezig wanneer de computer opnieuw wordt opgestart, moet je Diepvriezen toepassing in-
However, there are situations where entire folder present on desktop becomes invisible after computer is restarted.
Er zijn echter situaties waarin de hele map aanwezig zijn op het bureaublad wordt onzichtbaar nadat de computer opnieuw is opgestart.
Once the Minimal GUI start mode is selected and your computer is restarted, notifications will be displayed but the graphical interface will not.
Als de minimale gebruikersinterface als startmodus is geselecteerd en uw computer opnieuw is opgestart, worden er meldingen weergegeven maar wordt er geen grafische gebruikersinterface weergegeven.
the device is not enabled until the computer is restarted.
wordt het apparaat pas ingeschakeld als de computer opnieuw wordt opgestart.
The Message Queuing Triggers service will not monitor this re-created queue until the computer is restarted, or until the associated triggers are disabled,
De service Message Queuing Triggers controleert deze herstelde wachtrij pas als de computer opnieuw wordt opgestart of als de bijbehorende triggers worden uitgeschakeld
automatic configuration occurs only when the user's computer is restarted.
If Shutdown Event Tracker is enabled and your computer is restarted or shut down without a user entering a reason, the first member of the local Users group to log in after the restartis prompted to enter a reason for the event.
Als Afsluitgebeurtenis vastleggen is ingeschakeld en de computer opnieuw wordt opgestart of afgesloten zonder dat een gebruiker een reden opgeeft, wordt het eerste lid van de lokale groep Gebruikers dat zich aanmeldt na het opnieuw opstarten, gevraagd om een reden op te geven voor de gebeurtenis.
will continue to function until the computer is restarted.
blijft het actief totdat u de computer opnieuw opstart.
the DMA Locker virus causes a direct blue screen of death and after the computer is restarted the virus displays a system error
de DMA Locker virus veroorzaakt een directe blue screen of death en na de computer opnieuw is opgestart het virus vertoont een systeemfout
the device might continue to function until the computer is restarted.
blijft het apparaat mogelijk actief totdat u de computer opnieuw opstart.
When a computer is restarted on the network and, if at startup,
Als een computer opnieuw wordt opgestart op het netwerk en als de naam-
the Telephony snap-in might not display the lines and phones supported by the service provider until after the computer is restarted.
telefoons die door de serviceprovider worden ondersteund mogelijk pas in de module Telefonie weergegeven nadat de computer opnieuw is opgestart.
to be remembered until HIPS rules are changed, the HIPS filtering mode is changed, the HIPS module is updated or your computer is restarted.
de HIPS filtering functie wordt veranderd, de HIPS-module wordt bijgewerkt of de computer opnieuw wordt opgestart.
While your computer is restarting, hold down Command+ R to launch Recovery Mode.
Houd terwijl je computer opnieuw opstart Command+ R ingedrukt om de Recovery-modus te starten.
Press and hold the"C" key while the computer is restarting from the installation disc.
English
Deutsch
Español
Français
عربى
Български
বাংলা
Český
Dansk
Ελληνικά
Suomi
עִברִית
हिंदी
Hrvatski
Magyar
Bahasa indonesia
Italiano
日本語
Қазақ
한국어
മലയാളം
मराठी
Bahasa malay
Norsk
Polski
Português
Română
Русский
Slovenský
Slovenski
Српски
Svenska
தமிழ்
తెలుగు
ไทย
Tagalog
Turkce
Українська
اردو
Tiếng việt
中文