Examples of using Elastic modulus in English and their translations into Chinese
{-}
-
Political
-
Ecclesiastic
-
Programming
It has a high elastic modulus.
(5) Large elastic modulus, higher than cast iron.
弹性模量大，高于铸铁。Therefore, SiC has high hardness, large elastic modulus, and good wear resistance.
因此，SiC强度高、弹性模量大，具有优良的耐磨损性能。An elastic modulus of nearly 150 GPa, and a tensile strength of nearly 10 GPa.
弹性模量近似为150GPa，拉伸强度约为10GPa。Wood plastic composites materials contain plastics,so they have good elastic modulus.
木塑复合材料内含塑料，因此它具有较好的弹性模量。This makes the PDMS elastic modulus decrease by a factor of two.
这使得PDMS弹性模量减少了两倍。Strength: strength to consider its grip and anti-splitting performance and elastic modulus.
强度：强度应考虑其握力、抗劈裂性能和弹性模量。Tensile strength and elastic modulus is 125GPa and 1.1TPa, respectively.
其抗拉强度和弹性模量分别为125GPa和1.1TPa。Strength: strength to consider its grip and anti-splitting performance and elastic modulus.
强度：强度方面要考虑其握着力和抗劈性能及弹性模量。(3) elastic modulus is much smaller than the metal, can produce greater elastic deformation;
弹性模量远小于金属弹性模量，可产生较大的弹性变形；.Strength: the strength to take into account its grip andsplitting resistance and elastic modulus.
强度：强度应考虑其握力、抗劈裂性能和弹性模量。Lou and team measured the elastic modulus of molybdenum diselenide at 177.2(± 9.3) GPa.
JunLou和他的同事测量了二硒化钼的弹性模量，测试结果为177.2(±9.3)GPa。In terms of strength, the grip strength and the tamper resistance and elastic modulus should be considered.
就强度而言，应考虑抓地力以及抗篡改性和弹性模量。(3) elastic modulus is much smaller than the metal, can produce greater elastic deformation;
(3)橡胶减振器弹性模量比金属小得多，可产生较大弹性形变;Rigid PVC has good mechanical properties and its elastic modulus can reach 1500-3000MPa.
硬质PVC具有良好的机械性能，其弹性模量可达到1500-3000MPa。The elastic modulus of titanium alloy is about 1/2 of that of steel, so its rigidity is poor and easy to deform.
由于钛合金的弹性模量约为钢的1/2，因此其刚性差并且易于变形。The rigid PVC has good mechanical properties and its elastic modulus can reach 1500-3000 MPa.
硬质PVC具有良好的机械性能，其弹性模量可达到1500-3000MPa。The elastic modulus of rubber is smaller than that of metal, which can produce large elastic deformation;
(3)橡胶减振器弹性模量比金属小得多，可产生较大弹性形变;Low modulus of elasticity: titanium elastic modulus at normal temperature is 106.4 GMPa, 57% of the steel.
弹性模量低：钛的弹性模量在常温时为106.4GMPa,为钢的57%。The elastic modulus of titanium alloy is about 1/2 of that of steel, so its rigidity is poor and it is easily deformed.
由于钛合金的弹性模量约为钢的1/2，因此其刚性差并且易于变形。Although the tensile strength and IM7 are equivalent, but the elastic modulus achieved a substantial increase of 36%~ 28%.
虽然拉伸强度和IM7相当，但弹性模量实现了28%～36%的大幅提升。Elastic Modulus TC4 of E= 110GPa, about 1/2 of steel, it is prone to deformation when machining titanium alloys.
TC4的弹性模量E=110GPa，约为钢的1/2，故钛合金加工时容易产生变形。When drilling, due to the poor thermal conductivity of stainless steel materials,small elastic modulus, hole processing is also more difficult.
在钻孔加工时，由于不锈钢材料导热性能差，弹性模量小，孔加工起来也比较困难。(1) Modulus of elasticity- the elastic modulus of a material decreases as the hydrogen content increases;
Ti40Cu36Pd14Zr10 is believed to be noncarcinogenic,is about three times stronger than titanium, and its elastic modulus nearly matches bones.
非晶金属Ti40Cu36Pd14Zr10被认为是非致癌的，比钛强度大约三倍，其弹性模量与骨骼几乎相当。Elastic Modulus TC4 of E= 110GPa, about 1/2 of steel, it is prone to deformation when machining titanium alloys.
TC4的弹性模量E=110GPa,约为钢的1/2,故钛合金加工时容易产生变形。The elastic modulus maps, before(D) and after(E) stretch, are obtained with previously published analysis techniques13.
弹性模量的地图，之前（D）后（E）伸展，与此前公布的分析技术得到13。Low elastic modulus: The elastic modulus of titanium is 106.4GMPa at room temperature, which is 57% of steel.
弹性模量低：钛的弹性模量在常温时为106.4GMPa,为钢的57%。The elastic modulus of steel is nearly 200 times that of polyethylene(the elastic modulus of carbon steel is about 190000 MPa).
钢的弹性模量是聚乙烯的近200倍（碳素钢的弹性模量在1900….The tensile elastic modulus of carbon fiber manufactured by new manufacturing method is 240GPa, the tensile strength is 3.5GPa and the elongation reaches 1.5%.
用新制造方法制造的碳纤维的拉伸弹性模量为240GPa，拉伸强度为3.5GPa，延伸率达到1.5％。
