Examples of using Whose thickness in English and their translations into Slovenian
{-}
-
Colloquial
-
Official
-
Medicine
-
Ecclesiastic
-
Financial
-
Computer
-
Official/political
-
Programming
This work requires a material whose thickness is four centimeters.
Polycarbonate, whose thickness ranges from four to six millimeters, tightly connected to the arcs and transverse strips.
A glass cutter with a natural stone can cut glass whose thickness is 5-10 mm.
The table should be cut out of plywood, whose thickness should be at least 20 mm, then paste the textolite on the resulting rectangle.
The first stepis to make a template from hardwood hardwood, whose thickness is equal to 6 mm.
Sheets of plasterboard-the ceiling is usually installed from sheets whose thickness reaches 9 millimeters, with larger size there is a risk of some difficulties(a more durable frame construction or alternative installation technology is required);
Continental crust is also less thick than oceanic crust, whose thickness is about 2.9 g/cm3.
They offer certified boards, of trusted manufacturers, whose thickness goes from 1 to130mm, and which meet all the prescribed norms and standards.
In the supporting structures of greenhouses used galvanized corner, whose thickness is 1.5 mm.
Most modifications are equipped with cameras whose thickness does not exceed the range of 60-80 cm.
Warming of the ceiling between the basement andthe first floor is recommended to be performed with a material whose thickness is 20-30 cm.
Much more difficult to work with broadband rolled metal, whose thickness can reach 60 mm or more.
If you decide to decorate a greenhouse built with your own hands with a special film, then you should know thatexperts recommend turning to similar products whose thickness is at least 150 microns.
Any pool constructionimplies that fits the bottom of the sand layer, whose thickness is between 20 and 30 centimeters.
As an inexpensive and optimal variant of the tabletop for construction,the kitchen tabletop is made of chipboard, whose thickness is equal to 26 or 36 mm.
With it you can work with thin-sheet steel,welding parts and parts whose thickness is up to 0.5 mm;
If this material is not available,you can use MDF or laminated chipboard, whose thickness is limited to 16 mm.
It does not fit a simple film, which is used for insulation of houses or other structures,and it is suitable basalt cardboard, whose thickness should be at least 5 mm.
To make the maximum weatherability, a concrete tape is required, on the side where the building will be located,lay out a layer of foam, whose thickness will be from 30 to 50 millimeters.
Most often it is recommended to fill the tape at a level of 40-50 cm. As a rule,this figure does not include a so-called pillow, whose thickness should be at least 20 cm.
And this is one of the few collections of the manufacturer, whose board thickness is 12 mm.
Some methods of height classification limit the term vertical to upward-growing free-convective cumuliform andcumulonimbiform genera whose vertical thickness exceeds their horizontal base-width.
First you need to take a one-year-old good seedling, whose root necks have a thickness of at least 1 cm;
Let's suggest that the thickness of the paving slab, whose types are intended for pedestrian and automobile pavement sites, are different.
More precisely, tank-vehicles with mass less than 4 t used for local transport of gas oil only(UN 1202),first registered before 31/12/2002, whose shell thickness is less than 3mm, they are permitted to be in use only if they are transformed according to the marginal 211.127(5)b4(6.8.2.1.20).
In the case of steels used in the manufacture of vessels whose minimum working temperature is lower than-10 °C and whose wall thickness exceeds 5 mm, this property must be checked.
Then it transfers to the anilox roll whose texture holds a specific amount of ink since it is covered with thousands of small wells or cups that enable it to meter ink to the printing plate in a uniform thickness evenly and quickly(the number of cells per linear inch can vary according to the type of print job and the quality required).
Intended for through holes whose minimum and maximum diameter corresponds to the type of Snake Brace in relation to the actual thickness of the current structure.
Package thickness reduction We specialize in handling fine pitch components assembly and up to now we can deal with BGAs whose minimum pitch can be as small as 0.35mm.