Examples of using Should be connected in English and their translations into Thai
{-}
-
Colloquial
-
Ecclesiastic
-
Ecclesiastic
-
Computer
The external drain should be connected in the 3MPa~ 10MPa.
Motors are allowed to be connected in series and in parallel, and external drain pipes should be connected when used in series.
Lightning arrester should be connected to the shortest possible line.
If the one-bedroom Khrushchev, 60 square meters, has a balcony, it should be connected to a residential area.
If things should be connected permanently, adhesion and cohesion are in focus.
Now, your device(computer or the laptop) should be connected to the same network.
For aeration pump should be connected to a thin tube, which second end is over the water surface.
According to the arrow direction of rotation on the cover of the electric motor, the motor should be connected with stable wire and not reversed.
The grounded cable should be connected to the battery last.
When working with the Loyverse POS app on the Apple iOS device Socket 7Qi/7Ci(Bluetooth) scanner should be connected in Application Mode.
Then one wire from the lamp should be connected to the coil of the trambler.
Surface pumps for fountains and waterfallsis selected if the intended high and complex structures or the water features should be connected to a single pump.
WATER bundled with a vortex pump should be connected directly to the water supply.
I agree, never install any upgrades, everything might break, but to your point, look at the FAQ, this is probably the memory limit issue, but not that we see a reason why it should be connected to the upgrade.
The other end of the lighting cable should be connected either to a wall charger or a USB port.
The Light Sensor Module provides a very simple analog output, so all you need to connect it to your Arduino or compatible board such as the Eleven is GND, 5V, and one analog input. On a 3.3V microcontroller such as Freetronics EtherDue or Arduino Due, VCC should be connected to 3.3V instead of 5V.
Lead wire should be connected correctly according to grade that connecting diagram offers.
Industrial control signal lightning protection grounding should be connected to the ground through an electronic switch.
Even though it should be connected to the WAN side of the existing router, I routed it arbitrarily.
When the screw conveyor system is assembled in sections, the shaft head coupling between the screw should be connected in order to ensure the straightness of the whole screw.
The wire to motor should be connected according to the direction of motor rotation, reverse rotated is not allowed.
When the Dupont wire is used to connect the module to the Arduino UNO Baseboard, its RX andTX pins should be connected to digital port 0 and 1 respectively as follows.
Those 3 models should be connected with traditional test bench, which can test all common rail system CR PUMPS, CR INJECTORS, COMMON RAIL.
With a variety of work modes to chose, it can be one-way access, two-way access, control access by main board send switch signal it should be connected with control system, access control, fingerprint etc.
IN2: controls the second relay it should be connected to an Arduino digital pin if you are using this second relay. Otherwise, you don't need to connect it.
If the hydraulic hand operated pump needs to expand the usage like to meet activated cylinders requirement, the hydraulic hand operated pump may work under the pressure lower than 63MPa, In this case the pressure gauge should be connected to the hose, regulating high pressure valve until the showing pressure of pressure gauge reaches to the working pressure of cylinder.
Terminal WK: Is the switch and*wire“15” should be connected to this terminal- with the wire disconnected, the terminal should read less than 1 ohm to ground with genset off.
The neutral line(working zero line) of the generator should be connected to the grounding main line. The bolt anti-loose parts are complete and marked.
Terminal G: Is the sender and wire“OP” should be connected to this terminal- with the wire disconnected, the terminal should read close to 10 ohms to ground with genset off.
You can-but you should be aware that for your expert advisors or copy trading program to run efficiently, a single account should be connected to a single MT4 instance at any given time. You may have multiple accounts running on multiple MT4 instances, but these must be set up with caution as you need to consider the availability of your free server resources RAM/CPU.