Examples of using Curing time in English and their translations into Chinese
{-}
-
Political
-
Ecclesiastic
-
Programming
The curing time is relatively long, but the adhesion to most materials is excellent.
If the construction is in winter, then the curing time should be appropriately extended.
若是在冬季施工的话，那么固化时间还应适当延长。Short curing time and low carbon footprint are the benefits for the powder coating process.
固化时间短，碳足迹低，是粉末涂装工艺的优势所在。If the glass glue is partially orcompletely closed, the curing time is determined by the tightness of the seal.
如果玻璃胶部分或完全关闭，则固化时间由密封的紧密性决定。The curing time is generally three days, and the final strength of the test is generally ten days.
固化其固化时间一般为三天，检测最终强度一般为十天。Most thermoplastic elastomers do not require vulcanization orhave a short curing time, which can save energy.
大多数热塑性弹性体不需要硫化或具有短的固化时间，这节省了能量。The watering and curing time of the permeable floor should be no less than 7 days.
In contrast to the initial gluing solution,our blind rivet nuts have the advantage that they don‘t require curing time.
与最初的粘合式解决方案不同，我们的铆螺母优势在于不需要固化时间。Curing time can be divided into initial solid(or fixed)time and total solid time. .
固化时间可分为初固(或称固定)时间和全固时间。If the glass glue is partially orcompletely closed, the curing time is determined by the tightness of the seal.
如果硅酮密封剂是部分或完全封闭的，固化时间取决于密封的紧密性。Curing time is too long will cause the coating from dust, sand and other stolen goods, or even slow down period.
固化时间过长会造成涂膜沾染灰尘、沙粒等赃物，甚至会拖慢工期。PVP in oil production industry can be used as mud additive,increasing the viscosity and curing time, reducing the water loss rate.
PVP在采油工业中可作为泥浆添加剂，增加粘度和固化时间，降低失水率。固化：固化时间通常为三天，测试的最终强度通常为几天。The disadvantages are complicated operation, high difficulty,long curing time, slow speed, and difficulty in adapting to mass production.
缺点是操作复杂，难度大，固化时间长，速度慢，难以适应批量生产的要求。固化：固化时间一般为3天，试验的最终强度一般为10天。For this, Henkel has developed a polyurethane-basedcomposite matrix resin characterized by its short curing time and ease of use.
有鉴于此，汉高开发了一种基于聚氨酯的复合基体树脂，它具有固化时间短、易于使用的特点。At a temperature of 60°C, a curing time of 15 minutes is sufficient to achieve functional strength(>= 10 MPa).
例如，在60°C的温度下，固化时间仅需15分钟既能达到最终强度(>=10MPa)。Kerstan explains that with the LOCTITE MAX polyurethane systems,catalyst can be added to further reduce curing time, depending on part size.
Kerstan解释说，采用LOCTITEMAX聚氨酯树脂，可以根据部件大小而加入催化剂以进一步缩短固化时间。Controlling the curing time and appropriately reducing the curing temperature can reduce the transfer of aluminum plating.
控制固化时间，适当降低熟化温度可以减少镀铝的转移。Kerstan explained that with LOCTITE MAX polyurethane resin,catalyst can be added according to the size of the part to further shorten the curing time.
Kerstan解释说，采用LOCTITEMAX聚氨酯树脂，可以根据部件大小而加入催化剂以进一步缩短固化时间。Similarly, the heating and curing time and temperature can also change the hardness, and will not damage the other physical characteristics.
同样，固化时间和温度也可以改变硬度而不破坏其他物理特性。Compared to conventional manual lamination, the system's short curing time of between three and five minutes has a very positive effect on productivity.
系统具有的3至5分钟之间变化的短固化时间对生产力有着非常积极的影响。The curing time is usually 24 hours to reach the appropriate strength, 3-7 days to reach the maximum strength, with the change of temperature.
固化时间通常是24小时到达合适的强度，3-7天达到最高强度，随着温度的变化.(3) Steam curing can shorten the curing time, the template turnover rate is correspondingly increased, and the occupied space is greatly reduced.
三）蒸汽养护可缩短养护时间，模板周转率相应提高，占用场地大大减少。Working time and cure time depends on temperature and mass.
适用时间和固化时间取决于温度和混胶量：.For every 11 °C increase in material temperature, the cure time is reduced by half, but the lift temperature must not exceed the material's temperature.
材料温度每提升11℃，固化时间缩短一半，但提升温度不得超出材料的承受温度。固化温度-Araldite最低固化时间可从15小时到5分钟，降低固化温度增加68F到302F。Cure Times- The suggested Araldite 2011 cure time for most applications is 24 hours.
固化时间-建议Araldite2011对于大多数应用程序的固化时间为24小时。However, in many cases, the cure time may be accelerated with heat, but this is not required.
但是，在很多情况下，加热后固化时间可能缩短，不过并不需要这样。
