Examples of using Correction factor in English and their translations into Croatian
{-}
-
Colloquial
-
Ecclesiastic
-
Computer
I is the correction factor(La or Id).
Inductive Kplus sensors with correction factor 1+.
A correction factor shall be applied if necessary.
Spin stabilizer correction factor.
The correction factor aa is obtained by applying the formula.
Spin stabiliser correction factor.
Correction factor 1: Constant sensing range on all metals.
Determination of correction factor aa and ad(10).
Inductive Kplus sensors with constant correction factor 1.
The correction factor cf, which may be applied, is determined as follows.
If the viscosity value is out of range, a spindle correction factor can be stored on Toolmaster™.
The power correction factor(ad) for diesel engines at constant fuel rate is obtained by applying the formula.
The monitoring plan shall specify which distance calculation is used and, if necessary, the correction factor used.
For a test to be valid; the correction factor ad must be such that 0,9≤ ad≤ 1,1.
New electromagnetic field immune sensor technology prevents incorrect switching. Consistent correction factor.
For a test to be valid, the correction factor aa must be such that 0,93≤ aa≤ 1,07.
The energy efficiency formula value will be multiplied by a climate correction factor(CCF) as shown below.
Control factor(CTRL)' means a correction factor for the SEC calculation depending on the type of control that is part of the ventilation unit, according to the description in Annex VIII Table 1;
The proposed changes aim to minimise the need for a correction factor and to ensure predictability for companies.
For the Planck values(Ωm, ΩΛ)(0.3086, 0.6914),shown by the box in the upper left corner of the figure, this correction factor is about F 0.956.
Notwithstanding that, the application of such a correction factor should remain an incentive for incineration plants to achieve high efficiency of energy production from waste in line with the objectives and the waste hierarchy laid down in Directive 2008/98/EC.
The calculation is performed according to the standard parameters- 100 W of heat output per 1 square meter of area with the correction factor for the height of the room.
For plants witha net electrical efficiency(EE) greater than 55%, a correction factor may be applied to the higher end of the range, corresponding to[higher end]× EE/55, where EE is the net electrical energy efficiency of the plant determined at ISO baseload conditions.
The information is available that an employee had 20Â% of the reference month as unpaid absence,variable 3.2 will be multiplied by the correction factor 1,25.
(149) For plants with a net electrical efficiency(EE) greater than 55%, a correction factor may be applied to the higher end of the BAT-AEL range, corresponding to[higher end]× EE/55, where EE is the net electrical efficiency of the plant determined at ISO baseload conditions.
So, if you live in a cold region where winter temperatures are much lower than typical rates,it is necessary to multiply the figures by the correction factor of 1.1.
For plants witha net electrical efficiency(EE) greater than 39%, a correction factor may be applied to the higher end of this range, corresponding to[higher end]× EE/39, where EE is the net electrical energy efficiency or net mechanical energy efficiency of the plant determined at ISO baseload conditions.
If the device is still operating at 25 °C then the test is made with the device operating normally andthe exponent of the temperature term in the correction factor shall be taken as zero(no temperature correction). .
In the event that demand for free allowances triggers the need to apply a uniform cross-sectoral correction factor before 2030, the share of allowances to be auctioned over the ten year period beginning on 1 January 2021 should be reduced by up to 3% of the total quantity of allowances.
System hazardous areas(ATEX) electromagnetic field immune increased sensing range optical setting aid food industry metal sensing face mobile systems high temperature correction factor= 1 correction factor= 0 Analogue output 0… 10 V Analogue output 4… 20 mA.