Examples of using Maximum error in English and their translations into Russian
{-}
-
Official
-
Colloquial
The maximum error is εm" 3.
By picking the redundancy you will determine the maximum error correction capability.
Maximum error of measurement.
When determining ending times of tithis, these errors can result in a maximum error of 5 minutes of time.
Maximum error of measurement.
The DEM accuracy was 1.5 m andthat of the orthophotomap(rootmean-square error)- 0.56m, maximum error- 0.96 m.
Maximum errors of determination of.
Errors of measurements of the gravity field in the Arctic region average within+ 1-3 mGl range with maximum errors of+ 5 mGl.
The maximum error margin is 2.8 percent.
Reliability: the Department might establish quantifiable targets for reliability, such as maximum error rates;
Maximum error of measurement with test used.
If such facilities are provided, they shall be capable of taking a bearing of any target within approximately 5 seconds, with a maximum error of+- 1 degree.
K=. W/m2K Maximum error of measurement with test used.
The opinion poll was conducted by IMAS-Chisinau, at the initiative of IDIS“Viitorul”,on a sample of 1507 persons on 6- 27 March 2011, with a maximum error of±2.5%.
The maximum error of the measured value shall be within +-2 per cent of reading.
Vox Populi(November 12)- conducted by Moldovan Association of Sociologists and Demographers(ASDM)during 1- 10 November on a sample of 1,500 respondents with a maximum error of±2.6%.
The maximum error is observed for mixtures in which the content components differ by an order or more.
Vox Populi-II(November 22)- conducted by Moldovan Association of Sociologists and Demographers(ASDM)during 11- 20 November on a sample of 1,593 de respondents with a maximum error of±2.6%.
The maximum error allowed by a DMM depends not only on its variable term error, but also on its fixed term error. .
The poll was accomplished by the Association of Sociologists and Demographists of Moldova(ASDM)from November 1 to 10, on a sampling of 1,500 respondents, with a maximum error of approximately 2.6%.
The author clarifies the procedures that the maximum error can be± 10% due to the fact that the columns are often stopped, and the density of passenger traffic from time to time.
These estimates allow in practice to choice the optimal parameters of the whole algorithm andachieve the maximum possible acceleration of the computations for the given maximum error level.
The maximum error from the perfect round form of the boreholes must be no more than 30 micrometers- not even 0.01 percent of the diameter of the boreholes of 95 and 34 centimeters.
Barometer of Public Opinion(BOP)(November 16)- conducted by the Institute for Public Policy in cooperation with IMAS-INC Chisinau during 17 October- 7 November on a sample of 1,104 respondents with a maximum error of±3.0%.
If the gas flow is determined by differential flow measurement, the maximum error of the difference shall be such that the accuracy of GSE is within +-5 per cent when the dilution ratio is less than 15.
A high operational speed is the main feature of the given development: as computations are parallelized on both CPU and GPU, the computation time here getslower than with the COMSOL package; furthermore, the maximum error does not exceed 1.
If the gas flow is determined by differential flow measurement, the maximum error of the difference shall be such that the accuracy of GEDF is within 4 per cent see also Annex 4, Appendix 4, paragraph 1.2.1.1. EGA.
The onsite research of the survey“Vox Populi- August 2010”were carried out on August 9- 22, 2010 on a sample of 1594 respondents from 76 localities, representative for the adult population of Moldova(without Transnistrian region), with a maximum error of +2,6%.
If the gas flow is determined by differential flow measurement, the maximum error of the difference must be such that the accuracy of GEDF is within+- 4 per cent see also annex 4, appendix 7, paragraph 2.2.1., EGA.
The absolute accuracy of GTOTW and GDILW is within +-2 per cent of full scale, the maximum error of the difference between GTOTW and GDILW is within 0.2 per cent, and the linearity error is within +-0.2 per cent of the highest GTOTW observed during the test.