Examples of using Flashover in English and their translations into German
{-}
-
Colloquial
-
Official
-
Ecclesiastic
-
Medicine
-
Financial
-
Ecclesiastic
-
Political
-
Computer
-
Programming
-
Official/political
-
Political
Zero indication, breakdown flashover alarm.
Protection against flashover and accidentally induced discharge.
Longer insulator design offers best flashover protection.
At the same time, flashover can damage the surface of the casing.
Thus the insulation is damaged and a flashover may occur.
In this case, flashover is likely to occur, causing tripping.
It is easy to disconnect the power supply before reaching the flashover voltage again.
After flashover the fire reaches its maximum level and is fully developed.
Power to chassis frequency voltage withstands 1.5KV,1 min, no flashover and arcing.
The fuse holder can perform no breakdown or flashover in 400V AC voltage under the low pressure 40KPa.
Ivan_isaev loves this track ivan_isaevdoesn't love this track In Strict Confidence- Flashover.
Other problems include contact erosion, erosion by spark flashover, or arcing and welding at high power.
The tested cable must withstand a VLF(Very low frequency)AC voltage for a specified testing time without flashover.
It can quickly locate and point low resistance,high impedance fault leakage, flashover faults in power cable with a variety of 220V-220KV voltage level.
Dielectric Strength 1.5KV power supply chassis workfrequency withstand voltage 1 minute, no flashover and arcing.
In our flashover facility, students experience a flashover in real terms with all of their senses, so as to learn how to proceed safely even in extreme conditions of deployment.
On the second floor of the pyrodrome building you will find the bedroom with three fire seats: bed,headboard and flashover.
Flashover breakdown point, after breakdown the constant current source can maintain the arc, a stable current through the bridge, the bridge has enough sensitivity.
In the event of a partial discharge, secondary bubbles are also generated,further damaging the insulation and even flashover.
The instrument uses low-voltage pulse method and high-voltage flashover method to detect various faults of the cable, and directly test the flashover and high-resistance fault of the power cable without burning through.
The withstand voltage between grounding device and cabinet is no less than 3000V(DC)/min,no puncture, no flashover; U≥3000V.
ESD(Electrostatic Discharge) is a spark or flashover created by a major potential difference in an electrically isolated material, which causes a very short but, highly charged electrical impulse.
This valuable silicon grease convinces through its high dielectric breakdown voltage, is waterproof and UV-resistant-it even prevents flashover.
After the dirt absorbs moisture, the conductivity is improved,which not only causes surface flashover, but also may increase the leakage current, causing the insulation sleeve to heat up and cause porcelain damage or even breakdown.
The voltage resistance between the grounding device, and the box and its metal parts is no less than 3000V(DC)/min,no puncture, no flashover; U≥3000V.
The cut-off wave is a waveform that corresponds to a flashover of a protective gap or air insulation when a lightning wave enters a substation, and it is a waveform in which the entire lightning wave is abruptly cut off, and the voltage suddenly drops to zero.
The voltage resistance between the grounding device, and the box and its metal parts is no less than 3000V(DC)/min,no puncture, no flashover; U≥3000V.
Power cable testing car mainly on the high and low resistance of the cable grounding,high impedance flashover fault, short circuit and cable disconnection, poor contact failure test, and can be pinpointed, suitable for testing various models, different levels of voltage Power cables and communication cables of various failures.
The increasing dynamics of the sound(the airplane engine becoming louder) in contrast to the almost static image of the soldiers in the bushes(little movement within the shot, no camera movement) makesthe onset of movement within the frame(machine gun fire) seem like a flashover.
Under the action of the applied voltage, the leakage current of the insulator surface also increases greatly, which obviously reduces the insulation properties of the insulating material, and even causes the insulator's dirtylayer to generate heat, resulting in local arc or even full flashover.